-- Network Working Group C. Srinivasan
-- Request for Comments: 3812 Bloomberg L.P.
-- Category: Standards Track A. Viswanathan
-- Force10 Networks, Inc.
-- T. Nadeau
-- Cisco Systems, Inc.
-- June 2004-- Multiprotocol Label Switching (MPLS) Traffic Engineering (TE)
-- Management Information Base (MIB)MPLS-TE-STD-MIB DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,OBJECT-TYPE,NOTIFICATION-TYPE,Integer32,Unsigned32,Counter32,Counter64,TimeTicks,zeroDotZero
FROM SNMPv2-SMI -- [RFC2578]MODULE-COMPLIANCE,OBJECT-GROUP,NOTIFICATION-GROUP
FROM SNMPv2-CONF -- [RFC2580]TruthValue,RowStatus,RowPointer,StorageType,TimeStampFROM SNMPv2-TC -- [RFC2579]InterfaceIndexOrZero, ifGeneralInformationGroup,ifCounterDiscontinuityGroup
FROM IF-MIB -- [RFC2863]mplsStdMIB,MplsBitRate,MplsBurstSize,MplsLSPID,MplsTunnelIndex,MplsTunnelInstanceIndex,MplsTunnelAffinity,MplsExtendedTunnelId,MplsPathIndex,MplsPathIndexOrZero,MplsOwner,TeHopAddressType,TeHopAddress,TeHopAddressAS,TeHopAddressUnnumFROM MPLS-TC-STD-MIB -- [RFC3811]SnmpAdminStringFROM SNMP-FRAMEWORK-MIB -- [RFC3411]IndexIntegerNextFree
FROM DIFFSERV-MIB -- [RFC3289]InetAddressPrefixLengthFROM INET-ADDRESS-MIB -- [RFC3291];mplsTeStdMIB MODULE-IDENTITYLAST-UPDATED"200406030000Z"-- June 3, 2004ORGANIZATION"Multiprotocol Label Switching (MPLS) Working Group"CONTACT-INFO" Cheenu Srinivasan
Bloomberg L.P.
Email: cheenu@bloomberg.net
Arun Viswanathan
Force10 Networks, Inc.
Email: arunv@force10networks.com
Thomas D. Nadeau
Cisco Systems, Inc.
Email: tnadeau@cisco.com
Comments about this document should be emailed
directly to the MPLS working group mailing list at
mpls@uu.net."DESCRIPTION"Copyright (C) The Internet Society (2004). The
initial version of this MIB module was published
in RFC 3812. For full legal notices see the RFC
itself or see: http://www.ietf.org/copyrights/ianamib.html
This MIB module contains managed object definitions
for MPLS Traffic Engineering (TE) as defined in:
1. Extensions to RSVP for LSP Tunnels, Awduche et
al, RFC 3209, December 2001
2. Constraint-Based LSP Setup using LDP, Jamoussi
(Editor), RFC 3212, January 2002
3. Requirements for Traffic Engineering Over MPLS,
Awduche, D., Malcolm, J., Agogbua, J., O'Dell, M.,
and J. McManus, [RFC2702], September 1999"-- Revision history.
REVISION"200406030000Z"-- June 3, 2004DESCRIPTION"Initial version issued as part of RFC 3812."::={ mplsStdMIB 3}-- Top level components of this MIB module.-- trapsmplsTeNotifications OBJECTIDENTIFIER::={ mplsTeStdMIB 0}-- tables, scalarsmplsTeScalars OBJECTIDENTIFIER::={ mplsTeStdMIB 1}mplsTeObjects OBJECTIDENTIFIER::={ mplsTeStdMIB 2}-- conformancemplsTeConformance OBJECTIDENTIFIER::={ mplsTeStdMIB 3}-- MPLS Tunnel scalars.mplsTunnelConfigured OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of tunnels configured on this device. A
tunnel is considered configured if the
mplsTunnelRowStatus is active(1)."::={ mplsTeScalars 1}
mplsTunnelActive OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of tunnels active on this device. A
tunnel is considered active if the
mplsTunnelOperStatus is up(1)."::={ mplsTeScalars 2}mplsTunnelTEDistProto OBJECT-TYPESYNTAXBITS{other (0),ospf (1),isis (2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The traffic engineering distribution protocol(s)
used by this LSR. Note that an LSR may support more
than one distribution protocol simultaneously."::={ mplsTeScalars 3}mplsTunnelMaxHops OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The maximum number of hops that can be specified for
a tunnel on this device."::={ mplsTeScalars 4}mplsTunnelNotificationMaxRate OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This variable indicates the maximum number of
notifications issued per second. If events occur
more rapidly, the implementation may simply fail to
emit these notifications during that period, or may
queue them until an appropriate time. A value of 0
means no throttling is applied and events may be
notified at the rate at which they occur."DEFVAL{0}::={ mplsTeScalars 5}-- End of MPLS Tunnel scalars.-- MPLS tunnel table.mplsTunnelIndexNext OBJECT-TYPESYNTAXIndexIntegerNextFree(0..65535)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains an unused value for
mplsTunnelIndex, or a zero to indicate
that none exist. Negative values are not allowed,
as they do not correspond to valid values of
mplsTunnelIndex.
Note that this object offers an unused value
for an mplsTunnelIndex value at the ingress
side of a tunnel. At other LSRs the value
of mplsTunnelIndex SHOULD be taken from the
value signaled by the MPLS signaling protocol.
"::={ mplsTeObjects 1}mplsTunnelTable OBJECT-TYPESYNTAXSEQUENCEOF MplsTunnelEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The mplsTunnelTable allows new MPLS tunnels to be
created between an LSR and a remote endpoint, and
existing tunnels to be reconfigured or removed.
Note that only point-to-point tunnel segments are
supported, although multipoint-to-point and point-
to-multipoint connections are supported by an LSR
acting as a cross-connect. Each MPLS tunnel can
thus have one out-segment originating at this LSR
and/or one in-segment terminating at this LSR."::={ mplsTeObjects 2}mplsTunnelEntry OBJECT-TYPESYNTAX MplsTunnelEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in this table represents an MPLS tunnel.
An entry can be created by a network administrator
or by an SNMP agent as instructed by an MPLS
signalling protocol. Whenever a new entry is
created with mplsTunnelIsIf set to true(1), then a
corresponding entry is created in ifTable as well
(see RFC 2863). The ifType of this entry is
mplsTunnel(150).
A tunnel entry needs to be uniquely identified across
a MPLS network. Indices mplsTunnelIndex and
mplsTunnelInstance uniquely identify a tunnel on
the LSR originating the tunnel. To uniquely
identify a tunnel across an MPLS network requires
index mplsTunnelIngressLSRId. The last index
mplsTunnelEgressLSRId is useful in identifying all
instances of a tunnel that terminate on the same
egress LSR."REFERENCE"1. RFC 2863 - The Interfaces Group MIB, McCloghrie,
K., and F. Kastenholtz, June 2000 "INDEX{ mplsTunnelIndex,
mplsTunnelInstance,
mplsTunnelIngressLSRId,
mplsTunnelEgressLSRId
}::={ mplsTunnelTable 1}
MplsTunnelEntry ::=SEQUENCE{
mplsTunnelIndex MplsTunnelIndex,
mplsTunnelInstance MplsTunnelInstanceIndex,
mplsTunnelIngressLSRId MplsExtendedTunnelId,
mplsTunnelEgressLSRId MplsExtendedTunnelId,
mplsTunnelName SnmpAdminString,
mplsTunnelDescr SnmpAdminString,
mplsTunnelIsIf TruthValue,
mplsTunnelIfIndex InterfaceIndexOrZero,
mplsTunnelOwner MplsOwner,
mplsTunnelRole INTEGER,
mplsTunnelXCPointer RowPointer,
mplsTunnelSignallingProto INTEGER,
mplsTunnelSetupPrio Integer32,
mplsTunnelHoldingPrio Integer32,
mplsTunnelSessionAttributes BITS,
mplsTunnelLocalProtectInUse TruthValue,
mplsTunnelResourcePointer RowPointer,
mplsTunnelPrimaryInstance MplsTunnelInstanceIndex,
mplsTunnelInstancePriority Unsigned32,
mplsTunnelHopTableIndex MplsPathIndexOrZero,
mplsTunnelPathInUse MplsPathIndexOrZero,
mplsTunnelARHopTableIndex MplsPathIndexOrZero,
mplsTunnelCHopTableIndex MplsPathIndexOrZero,
mplsTunnelIncludeAnyAffinity MplsTunnelAffinity,
mplsTunnelIncludeAllAffinity MplsTunnelAffinity,
mplsTunnelExcludeAnyAffinity MplsTunnelAffinity,
mplsTunnelTotalUpTime TimeTicks,
mplsTunnelInstanceUpTime TimeTicks,
mplsTunnelPrimaryUpTime TimeTicks,
mplsTunnelPathChanges Counter32,
mplsTunnelLastPathChange TimeTicks,
mplsTunnelCreationTime TimeStamp,
mplsTunnelStateTransitions Counter32,
mplsTunnelAdminStatus INTEGER,
mplsTunnelOperStatus INTEGER,
mplsTunnelRowStatus RowStatus,
mplsTunnelStorageType StorageType}mplsTunnelIndex OBJECT-TYPESYNTAXMplsTunnelIndexMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Uniquely identifies a set of tunnel instances
between a pair of ingress and egress LSRs.
Managers should obtain new values for row
creation in this table by reading
mplsTunnelIndexNext. When
the MPLS signalling protocol is rsvp(2) this value
SHOULD be equal to the value signaled in the
Tunnel Id of the Session object. When the MPLS
signalling protocol is crldp(3) this value
SHOULD be equal to the value signaled in the
LSP ID."::={ mplsTunnelEntry 1}mplsTunnelInstance OBJECT-TYPESYNTAXMplsTunnelInstanceIndexMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION
"Uniquely identifies a particular instance of a
tunnel between a pair of ingress and egress LSRs.
It is useful to identify multiple instances of
tunnels for the purposes of backup and parallel
tunnels. When the MPLS signaling protocol is
rsvp(2) this value SHOULD be equal to the LSP Id
of the Sender Template object. When the signaling
protocol is crldp(3) there is no equivalent
signaling object."::={ mplsTunnelEntry 2}mplsTunnelIngressLSRId OBJECT-TYPESYNTAXMplsExtendedTunnelIdMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Identity of the ingress LSR associated with this
tunnel instance. When the MPLS signalling protocol
is rsvp(2) this value SHOULD be equal to the Tunnel
Sender Address in the Sender Template object and MAY
be equal to the Extended Tunnel Id field in the
SESSION object. When the MPLS signalling protocol is
crldp(3) this value SHOULD be equal to the Ingress
LSR Router ID field in the LSPID TLV object."REFERENCE"1. RSVP-TE: Extensions to RSVP for LSP Tunnels,
Awduche et al, RFC 3209, December 2001
2. Constraint-Based LSP Setup using LDP, Jamoussi
(Editor), RFC 3212, January 2002"::={ mplsTunnelEntry 3}mplsTunnelEgressLSRId OBJECT-TYPESYNTAXMplsExtendedTunnelIdMAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"Identity of the egress LSR associated with this
tunnel instance."::={ mplsTunnelEntry 4}mplsTunnelName OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The canonical name assigned to the tunnel. This name
can be used to refer to the tunnel on the LSR's
console port. If mplsTunnelIsIf is set to true
then the ifName of the interface corresponding to
this tunnel should have a value equal to
mplsTunnelName. Also see the description of ifName
in RFC 2863."REFERENCE"RFC 2863 - The Interfaces Group MIB, McCloghrie, K.,
and F. Kastenholtz, June 2000"DEFVAL{""}::={ mplsTunnelEntry 5}mplsTunnelDescr OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-createSTATUScurrentDESCRIPTION"A textual string containing information about the
tunnel. If there is no description this object
contains a zero length string. This object is may
not be signaled by MPLS signaling protocols,
consequentally the value of this object at transit
and egress LSRs MAY be automatically generated or
absent."DEFVAL{""}::={ mplsTunnelEntry 6}mplsTunnelIsIf OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Denotes whether or not this tunnel corresponds to an
interface represented in the interfaces group
table. Note that if this variable is set to true
then the ifName of the interface corresponding to
this tunnel should have a value equal to
mplsTunnelName. Also see the description of ifName
in RFC 2863. This object is meaningful only at the
ingress and egress LSRs."REFERENCE"RFC 2863 - The Interfaces Group MIB, McCloghrie, K.,
and F. Kastenholtz, June 2000"DEFVAL{ false }::={ mplsTunnelEntry 7}mplsTunnelIfIndex OBJECT-TYPESYNTAXInterfaceIndexOrZeroMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If mplsTunnelIsIf is set to true, then this value
contains the LSR-assigned ifIndex which corresponds
to an entry in the interfaces table. Otherwise
this variable should contain the value of zero
indicating that a valid ifIndex was not assigned to
this tunnel interface."REFERENCE"RFC 2863 - The Interfaces Group MIB, McCloghrie, K.,
and F. Kastenholtz, June 2000"DEFVAL{0}::={ mplsTunnelEntry 8}mplsTunnelOwner OBJECT-TYPESYNTAXMplsOwnerMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Denotes the entity that created and is responsible
for managing this tunnel. This column is
automatically filled by the agent on creation of a
row."::={ mplsTunnelEntry 9}mplsTunnelRole OBJECT-TYPESYNTAXINTEGER{ head(1),transit(2),tail(3),headTail(4)}MAX-ACCESSread-createSTATUScurrent
DESCRIPTION"This value signifies the role that this tunnel
entry/instance represents. This value MUST be set
to head(1) at the originating point of the tunnel.
This value MUST be set to transit(2) at transit
points along the tunnel, if transit points are
supported. This value MUST be set to tail(3) at the
terminating point of the tunnel if tunnel tails are
supported.
The value headTail(4) is provided for tunnels that
begin and end on the same LSR."DEFVAL{ head }::={ mplsTunnelEntry 10}mplsTunnelXCPointer OBJECT-TYPESYNTAXRowPointerMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This variable points to a row in the mplsXCTable.
This table identifies the segments that compose
this tunnel, their characteristics, and
relationships to each other. A value of zeroDotZero
indicates that no LSP has been associated with this
tunnel yet."REFERENCE"Srinivasan, C., Viswanathan, A., and T. Nadeau,
Multiprotocol Label Switching (MPLS) Label Switching
Router (LSR) Management Information Base (MIB), RFC 3813,
June 2004"DEFVAL{ zeroDotZero }::={ mplsTunnelEntry 11}mplsTunnelSignallingProto OBJECT-TYPE
SYNTAXINTEGER{none(1),rsvp(2),crldp(3),other(4)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The signalling protocol, if any, used to setup this
tunnel."DEFVAL{ none }::={ mplsTunnelEntry 12}mplsTunnelSetupPrio OBJECT-TYPESYNTAXInteger32(0..7)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates the setup priority of this tunnel."REFERENCE"1. RSVP-TE: Extensions to RSVP for LSP Tunnels,
Awduche et al, RFC 3209, December 2001
2. Constraint-Based LSP Setup using LDP, Jamoussi
(Editor), RFC 3212, January 2002"DEFVAL{0}
::={ mplsTunnelEntry 13}mplsTunnelHoldingPrio OBJECT-TYPESYNTAXInteger32(0..7)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates the holding priority for this tunnel."REFERENCE"1. RSVP-TE: Extensions to RSVP for LSP Tunnels,
Awduche et al, RFC 3209, December 2001
2. Constraint-Based LSP Setup using LDP, Jamoussi
(Editor), RFC 3212, January 2002"DEFVAL{0}::={ mplsTunnelEntry 14}mplsTunnelSessionAttributes OBJECT-TYPESYNTAXBITS{fastReroute (0),mergingPermitted (1),isPersistent (2),isPinned (3),recordRoute(4)}MAX-ACCESSread-create
STATUScurrentDESCRIPTION"This bit mask indicates optional session values for
this tunnel. The following describes these bit
fields:
fastRerouteThis flag indicates that the any tunnel
hop may choose to reroute this tunnel without
tearing it down. This flag permits transit routers
to use a local repair mechanism which may result in
violation of the explicit routing of this tunnel.
When a fault is detected on an adjacent downstream
link or node, a transit router can re-route traffic
for fast service restoration.
mergingPermitted This flag permits transit routers
to merge this session with other RSVP sessions for
the purpose of reducing resource overhead on
downstream transit routers, thereby providing
better network scaling.
isPersistent Indicates whether this tunnel should
be restored automatically after a failure occurs.
isPinned This flag indicates whether the loose-
routed hops of this tunnel are to be pinned.
recordRouteThis flag indicates whether or not the
signalling protocol should remember the tunnel path
after it has been signaled."REFERENCE"1. RSVP-TE: Extensions to RSVP for LSP Tunnels,
Awduche et al, RFC 3209, December 2001."::={ mplsTunnelEntry 15}mplsTunnelLocalProtectInUse OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates that the local repair mechanism is in use
to maintain this tunnel (usually in the face of an
outage of the link it was previously routed over)."DEFVAL{ false }::={ mplsTunnelEntry 16}mplsTunnelResourcePointer OBJECT-TYPESYNTAXRowPointerMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This variable represents a pointer to the traffic
parameter specification for this tunnel. This
value may point at an entry in the
mplsTunnelResourceEntry to indicate which
mplsTunnelResourceEntry is to be assigned to this
LSP instance. This value may optionally point at
an externally defined traffic parameter
specification table. A value of zeroDotZero
indicates best-effort treatment. By having the
same value of this object, two or more LSPs can
indicate resource sharing."DEFVAL{ zeroDotZero }::={ mplsTunnelEntry 17}mplsTunnelPrimaryInstance OBJECT-TYPESYNTAXMplsTunnelInstanceIndexMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Specifies the instance index of the primary instance
of this tunnel. More details of the definition of
tunnel instances and the primary tunnel instance
can be found in the description of the TEXTUAL-CONVENTION
MplsTunnelInstanceIndex."DEFVAL{0}::={ mplsTunnelEntry 18}mplsTunnelInstancePriority OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This value indicates which priority, in descending
order, with 0 indicating the lowest priority,
within a group of tunnel instances. A group of
tunnel instances is defined as a set of LSPs with
the same mplsTunnelIndex in this table, but with a
different mplsTunnelInstance. Tunnel instance
priorities are used to denote the priority at which
a particular tunnel instance will supercede
another. Instances of tunnels containing the same
mplsTunnelInstancePriority will be used for load
sharing."DEFVAL{0}::={ mplsTunnelEntry 19}mplsTunnelHopTableIndex OBJECT-TYPESYNTAXMplsPathIndexOrZeroMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Index into the mplsTunnelHopTable entry that
specifies the explicit route hops for this tunnel.
This object is meaningful only at the head-end of
the tunnel."DEFVAL{0}::={ mplsTunnelEntry 20}mplsTunnelPathInUse OBJECT-TYPESYNTAXMplsPathIndexOrZeroMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This value denotes the configured path that was
chosen for this tunnel. This value reflects the
secondary index into mplsTunnelHopTable. This path
may not exactly match the one in
mplsTunnelARHopTable due to the fact that some CSPF
modification may have taken place. See
mplsTunnelARHopTable for the actual path being
taken by the tunnel. A value of zero denotes that
no path is currently in use or available."DEFVAL{0}::={ mplsTunnelEntry 21}mplsTunnelARHopTableIndex OBJECT-TYPESYNTAXMplsPathIndexOrZeroMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Index into the mplsTunnelARHopTable entry that
specifies the actual hops traversed by the tunnel.
This is automatically updated by the agent when the
actual hops becomes available."
DEFVAL{0}::={ mplsTunnelEntry 22}mplsTunnelCHopTableIndex OBJECT-TYPESYNTAXMplsPathIndexOrZeroMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Index into the mplsTunnelCHopTable entry that
specifies the computed hops traversed by the
tunnel. This is automatically updated by the agent
when computed hops become available or when
computed hops get modified."DEFVAL{0}::={ mplsTunnelEntry 23}mplsTunnelIncludeAnyAffinity OBJECT-TYPESYNTAXMplsTunnelAffinityMAX-ACCESSread-createSTATUScurrentDESCRIPTION"A link satisfies the include-any constraint if and
only if the constraint is zero, or the link and the
constraint have a resource class in common."REFERENCE"1. RSVP-TE: Extensions to RSVP for LSP Tunnels,
Awduche et al, RFC 3209, December 2001."::={ mplsTunnelEntry 24}mplsTunnelIncludeAllAffinity OBJECT-TYPESYNTAXMplsTunnelAffinity
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"A link satisfies the include-all constraint if and
only if the link contains all of the administrative
groups specified in the constraint."REFERENCE"1. RSVP-TE: Extensions to RSVP for LSP Tunnels,
Awduche et al, RFC 3209, December 2001."::={ mplsTunnelEntry 25}mplsTunnelExcludeAnyAffinity OBJECT-TYPESYNTAXMplsTunnelAffinityMAX-ACCESSread-createSTATUScurrentDESCRIPTION"A link satisfies the exclude-any constraint if and
only if the link contains none of the
administrative groups specified in the constraint."REFERENCE"1. RSVP-TE: Extensions to RSVP for LSP Tunnels,
Awduche et al, RFC 3209, December 2001."DEFVAL{0}::={ mplsTunnelEntry 26}mplsTunnelTotalUpTime OBJECT-TYPESYNTAXTimeTicksMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This value represents the aggregate up time for all
instances of this tunnel, if available. If this
value is unavailable, it MUST return a value of 0."::={ mplsTunnelEntry 27}mplsTunnelInstanceUpTime OBJECT-TYPESYNTAXTimeTicksMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This value identifies the total time that this
tunnel instance's operStatus has been Up(1)."::={ mplsTunnelEntry 28}mplsTunnelPrimaryUpTime OBJECT-TYPESYNTAXTimeTicksMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Specifies the total time the primary instance of
this tunnel has been active. The primary instance
of this tunnel is defined in
mplsTunnelPrimaryInstance."::={ mplsTunnelEntry 29}mplsTunnelPathChanges OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Specifies the number of times the actual path for
this tunnel instance has changed."::={ mplsTunnelEntry 30}
mplsTunnelLastPathChange OBJECT-TYPESYNTAXTimeTicksMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Specifies the time since the last change to the
actual path for this tunnel instance."::={ mplsTunnelEntry 31}mplsTunnelCreationTime OBJECT-TYPESYNTAXTimeStampMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Specifies the value of SysUpTime when the first
instance of this tunnel came into existence.
That is, when the value of mplsTunnelOperStatus
was first set to up(1)."::={ mplsTunnelEntry 32}mplsTunnelStateTransitions OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Specifies the number of times the state
(mplsTunnelOperStatus) of this tunnel instance has
changed."::={ mplsTunnelEntry 33}mplsTunnelAdminStatus OBJECT-TYPESYNTAXINTEGER{
-- ready to pass packetsup(1),down(2),-- in some test modetesting(3)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates the desired operational status of this
tunnel."::={ mplsTunnelEntry 34}mplsTunnelOperStatus OBJECT-TYPESYNTAXINTEGER{-- ready to pass packetsup(1),down(2),-- in some test modetesting(3),-- status cannot be determinedunknown(4),dormant(5),-- some component is missingnotPresent(6),
-- down due to the state of-- lower layer interfaceslowerLayerDown(7)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the actual operational status of this
tunnel, which is typically but not limited to, a
function of the state of individual segments of
this tunnel."::={ mplsTunnelEntry 35}mplsTunnelRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This variable is used to create, modify, and/or
delete a row in this table. When a row in this
table is in active(1) state, no objects in that row
can be modified by the agent except
mplsTunnelAdminStatus, mplsTunnelRowStatus and
mplsTunnelStorageType."::={ mplsTunnelEntry 36}mplsTunnelStorageType OBJECT-TYPESYNTAXStorageTypeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The storage type for this tunnel entry.
Conceptual rows having the value 'permanent'
need not allow write-access to any columnar
objects in the row."DEFVAL{ volatile }::={ mplsTunnelEntry 37}-- End of mplsTunnelTablemplsTunnelHopListIndexNext OBJECT-TYPESYNTAXMplsPathIndexOrZeroMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains an appropriate value to be used
for mplsTunnelHopListIndex when creating entries in
the mplsTunnelHopTable. If the number of
unassigned entries is exhausted, a retrieval
operation will return a value of 0. This object
may also return a value of 0 when the LSR is unable
to accept conceptual row creation, for example, if
the mplsTunnelHopTable is implemented as read-only.
To obtain the value of mplsTunnelHopListIndex for a
new entry in the mplsTunnelHopTable, the manager
issues a management protocol retrieval operation to
obtain the current value of mplsTunnelHopIndex.
When the SET is performed to create a row in the
mplsTunnelHopTable, the Command Responder (agent)
must determine whether the value is indeed still
unused; Two Network Management Applications may
attempt to create a row (configuration entry)
simultaneously and use the same value. If it is
currently unused, the SET succeeds and the Command
Responder (agent) changes the value of this object,
according to an implementation-specific algorithm.
If the value is in use, however, the SET fails. The
Network Management Application must then re-read
this variable to obtain a new usable value."::={ mplsTeObjects 3}mplsTunnelHopTable OBJECT-TYPESYNTAXSEQUENCEOF MplsTunnelHopEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The mplsTunnelHopTable is used to indicate the hops,
strict or loose, for an instance of an MPLS tunnel
defined in mplsTunnelTable, when it is established
via signalling, for the outgoing direction of the
tunnel. Thus at a transit LSR, this table contains
the desired path of the tunnel from this LSR
onwards. Each row in this table is indexed by
mplsTunnelHopListIndex which corresponds to a group
of hop lists or path options. Each row also has a
secondary index mplsTunnelHopIndex, which indicates
a group of hops (also known as a path option).
Finally, the third index, mplsTunnelHopIndex
indicates the specific hop information for a path
option. In case we want to specify a particular
interface on the originating LSR of an outgoing
tunnel by which we want packets to exit the LSR,
we specify this as the first hop for this tunnel in
mplsTunnelHopTable."::={ mplsTeObjects 4}mplsTunnelHopEntry OBJECT-TYPESYNTAX MplsTunnelHopEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"An entry in this table represents a tunnel hop. An
entry is created by a network administrator for
signaled ERLSP set up by an MPLS signalling
protocol."INDEX{
mplsTunnelHopListIndex,
mplsTunnelHopPathOptionIndex,
mplsTunnelHopIndex
}::={ mplsTunnelHopTable 1}
MplsTunnelHopEntry ::=SEQUENCE{
mplsTunnelHopListIndex MplsPathIndex,
mplsTunnelHopPathOptionIndex MplsPathIndex,
mplsTunnelHopIndex MplsPathIndex,
mplsTunnelHopAddrType TeHopAddressType,
mplsTunnelHopIpAddr TeHopAddress,
mplsTunnelHopIpPrefixLen InetAddressPrefixLength,
mplsTunnelHopAsNumber TeHopAddressAS,
mplsTunnelHopAddrUnnum TeHopAddressUnnum,
mplsTunnelHopLspId MplsLSPID,
mplsTunnelHopType INTEGER,
mplsTunnelHopInclude TruthValue,
mplsTunnelHopPathOptionName SnmpAdminString,
mplsTunnelHopEntryPathComp INTEGER,
mplsTunnelHopRowStatus RowStatus,
mplsTunnelHopStorageType StorageType}mplsTunnelHopListIndex OBJECT-TYPESYNTAXMplsPathIndexMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Primary index into this table identifying a
particular explicit route object."::={ mplsTunnelHopEntry 1}mplsTunnelHopPathOptionIndex OBJECT-TYPESYNTAXMplsPathIndexMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Secondary index into this table identifying a
particular group of hops representing a particular
configured path. This is otherwise known as a path
option."::={ mplsTunnelHopEntry 2}mplsTunnelHopIndex OBJECT-TYPESYNTAXMplsPathIndexMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Tertiary index into this table identifying a
particular hop."::={ mplsTunnelHopEntry 3}
mplsTunnelHopAddrType OBJECT-TYPESYNTAXTeHopAddressTypeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The Hop Address Type of this tunnel hop.
The value of this object cannot be changed
if the value of the corresponding
mplsTunnelHopRowStatus object is 'active'.
Note that lspid(5) is a valid option only
for tunnels signaled via CRLDP.
"DEFVAL{ ipv4 }::={ mplsTunnelHopEntry 4}mplsTunnelHopIpAddr OBJECT-TYPESYNTAXTeHopAddressMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The Tunnel Hop Address for this tunnel hop.
The type of this address is determined by the
value of the corresponding mplsTunnelHopAddrType.
The value of this object cannot be changed
if the value of the corresponding
mplsTunnelHopRowStatus object is 'active'.
"DEFVAL{ '00000000'h }-- IPv4 address 0.0.0.0::={ mplsTunnelHopEntry 5}mplsTunnelHopIpPrefixLen OBJECT-TYPE
SYNTAXInetAddressPrefixLengthMAX-ACCESSread-createSTATUScurrentDESCRIPTION"If mplsTunnelHopAddrType is set to ipv4(1) or
ipv6(2), then this value will contain an
appropriate prefix length for the IP address in
object mplsTunnelHopIpAddr. Otherwise this value
is irrelevant and should be ignored.
"DEFVAL{32}::={ mplsTunnelHopEntry 6}mplsTunnelHopAsNumber OBJECT-TYPESYNTAXTeHopAddressASMAX-ACCESSread-createSTATUScurrentDESCRIPTION"If mplsTunnelHopAddrType is set to asnumber(3), then
this value will contain the AS number of this hop.
Otherwise the agent should set this object to zero-
length string and the manager should ignore this."::={ mplsTunnelHopEntry 7}mplsTunnelHopAddrUnnum OBJECT-TYPESYNTAXTeHopAddressUnnumMAX-ACCESSread-createSTATUScurrentDESCRIPTION"If mplsTunnelHopAddrType is set to unnum(4), then
this value will contain the interface identifier of
the unnumbered interface for this hop. This object
should be used in conjunction with
mplsTunnelHopIpAddress which would contain the LSR
Router ID in this case. Otherwise the agent should
set this object to zero-length string and the
manager should ignore this."::={ mplsTunnelHopEntry 8}mplsTunnelHopLspId OBJECT-TYPESYNTAXMplsLSPIDMAX-ACCESSread-createSTATUScurrentDESCRIPTION"If mplsTunnelHopAddrType is set to lspid(5), then
this value will contain the LSPID of a tunnel of
this hop. The present tunnel being configured is
tunneled through this hop (using label stacking).
This object is otherwise insignificant and should
contain a value of 0 to indicate this fact."::={ mplsTunnelHopEntry 9}mplsTunnelHopType OBJECT-TYPESYNTAXINTEGER{strict(1),loose(2)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Denotes whether this tunnel hop is routed in a
strict or loose fashion. The value of this object
has no meaning if the mplsTunnelHopInclude object
is set to 'false'."::={ mplsTunnelHopEntry 10}mplsTunnelHopInclude OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUScurrentDESCRIPTION"If this value is set to true, then this indicates
that this hop must be included in the tunnel's
path. If this value is set to 'false', then this hop
must be avoided when calculating the path for this
tunnel. The default value of this object is 'true',
so that by default all indicated hops are included
in the CSPF path computation. If this object is set
to 'false' the value of mplsTunnelHopType should be
ignored."DEFVAL{ true }::={ mplsTunnelHopEntry 11}mplsTunnelHopPathOptionName OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The description of this series of hops as they
relate to the specified path option. The
value of this object SHOULD be the same for
each hop in the series that comprises a
path option."::={ mplsTunnelHopEntry 12}
mplsTunnelHopEntryPathComp OBJECT-TYPESYNTAXINTEGER{dynamic(1),-- CSPF computedexplicit(2)-- strict hop}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"If this value is set to dynamic, then the user
should only specify the source and destination of
the path and expect that the CSPF will calculate
the remainder of the path. If this value is set to
explicit, the user should specify the entire path
for the tunnel to take. This path may contain
strict or loose hops. Each hop along a specific
path SHOULD have this object set to the same value"::={ mplsTunnelHopEntry 13}mplsTunnelHopRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This variable is used to create, modify, and/or
delete a row in this table. When a row in this
table is in active(1) state, no objects in that row
can be modified by the agent except
mplsTunnelHopRowStatus and
mplsTunnelHopStorageType."
::={ mplsTunnelHopEntry 14}mplsTunnelHopStorageType OBJECT-TYPESYNTAXStorageTypeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The storage type for this Hop entry. Conceptual
rows having the value 'permanent' need not
allow write-access to any columnar objects
in the row."DEFVAL{ volatile }::={ mplsTunnelHopEntry 15}-- End of mplsTunnelHopTable-- Begin of mplsTunnelResourceTablemplsTunnelResourceIndexNext OBJECT-TYPESYNTAXUnsigned32(0..2147483647)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the next appropriate value to
be used for mplsTunnelResourceIndex when creating
entries in the mplsTunnelResourceTable. If the
number of unassigned entries is exhausted, a
retrieval operation will return a value of 0. This
object may also return a value of 0 when the LSR is
unable to accept conceptual row creation, for
example, if the mplsTunnelTable is implemented as
read-only. To obtain the mplsTunnelResourceIndex
value for a new entry, the manager must first issue
a management protocol retrieval operation to obtain
the current value of this object.
When the SET is performed to create a row in the
mplsTunnelResourceTable, the Command Responder
(agent) must determine whether the value is indeed
still unused; Two Network Management Applications
may attempt to create a row (configuration entry)
simultaneously and use the same value. If it is
currently unused, the SET succeeds and the Command
Responder (agent) changes the value of this object,
according to an implementation-specific algorithm.
If the value is in use, however, the SET fails. The
Network Management Application must then re-read
this variable to obtain a new usable value."::={ mplsTeObjects 5}mplsTunnelResourceTable OBJECT-TYPESYNTAXSEQUENCEOF MplsTunnelResourceEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The mplsTunnelResourceTable allows a manager to
specify which resources are desired for an MPLS
tunnel. This table also allows several tunnels to
point to a single entry in this table, implying
that these tunnels should share resources."::={ mplsTeObjects 6}mplsTunnelResourceEntry OBJECT-TYPESYNTAX MplsTunnelResourceEntry
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"An entry in this table represents a set of resources
for an MPLS tunnel. An entry can be created by a
network administrator or by an SNMP agent as
instructed by any MPLS signalling protocol.
An entry in this table referenced by a tunnel instance
with zero mplsTunnelInstance value indicates a
configured set of resource parameter. An entry
referenced by a tunnel instance with a non-zero
mplsTunnelInstance reflects the in-use resource
parameters for the tunnel instance which may have
been negotiated or modified by the MPLS signaling
protocols."INDEX{ mplsTunnelResourceIndex }::={ mplsTunnelResourceTable 1}
MplsTunnelResourceEntry ::=SEQUENCE{
mplsTunnelResourceIndex Unsigned32,
mplsTunnelResourceMaxRate MplsBitRate,
mplsTunnelResourceMeanRate MplsBitRate,
mplsTunnelResourceMaxBurstSize MplsBurstSize,
mplsTunnelResourceMeanBurstSize MplsBurstSize,
mplsTunnelResourceExBurstSize MplsBurstSize,
mplsTunnelResourceFrequency INTEGER,
mplsTunnelResourceWeight Unsigned32,
mplsTunnelResourceRowStatus RowStatus,
mplsTunnelResourceStorageType StorageType}mplsTunnelResourceIndex OBJECT-TYPESYNTAXUnsigned32(1..2147483647)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Uniquely identifies this row."::={ mplsTunnelResourceEntry 1}mplsTunnelResourceMaxRate OBJECT-TYPESYNTAXMplsBitRateUNITS"kilobits per second"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The maximum rate in bits/second. Note that setting
mplsTunnelResourceMaxRate,
mplsTunnelResourceMeanRate, and
mplsTunnelResourceMaxBurstSize to 0 indicates best-
effort treatment."::={ mplsTunnelResourceEntry 2}mplsTunnelResourceMeanRate OBJECT-TYPESYNTAXMplsBitRateUNITS"kilobits per second"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object is copied into an instance of
mplsTrafficParamMeanRate in the
mplsTrafficParamTable. The OID of this table entry
is then copied into the corresponding
mplsInSegmentTrafficParamPtr."::={ mplsTunnelResourceEntry 3}mplsTunnelResourceMaxBurstSize OBJECT-TYPESYNTAXMplsBurstSizeUNITS"bytes"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The maximum burst size in bytes."::={ mplsTunnelResourceEntry 4}mplsTunnelResourceMeanBurstSize OBJECT-TYPESYNTAXMplsBurstSizeUNITS"bytes"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The mean burst size in bytes. The implementations
which do not implement this variable must return
a noSuchObject exception for this object and must
not allow a user to set this object."::={ mplsTunnelResourceEntry 5}mplsTunnelResourceExBurstSize OBJECT-TYPESYNTAXMplsBurstSizeUNITS"bytes"MAX-ACCESSread-create
STATUScurrentDESCRIPTION"The Excess burst size in bytes. The implementations
which do not implement this variable must return
noSuchObject exception for this object and must
not allow a user to set this value."REFERENCE"CR-LDP Specification, Section 4.3."::={ mplsTunnelResourceEntry 6}mplsTunnelResourceFrequency OBJECT-TYPESYNTAXINTEGER{ unspecified(1),frequent(2),veryFrequent(3)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The granularity of the availability of committed
rate. The implementations which do not implement
this variable must return unspecified(1) for this
value and must not allow a user to set this value."REFERENCE"CR-LDP Specification, Section 4.3."::={ mplsTunnelResourceEntry 7}mplsTunnelResourceWeight OBJECT-TYPESYNTAXUnsigned32(0..255)
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The relative weight for using excess bandwidth above
its committed rate. The value of 0 means that
weight is not applicable for the CR-LSP."REFERENCE"CR-LDP Specification, Section 4.3."::={ mplsTunnelResourceEntry 8}mplsTunnelResourceRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This variable is used to create, modify, and/or
delete a row in this table. When a row in this
table is in active(1) state, no objects in that row
can be modified by the agent except
mplsTunnelResourceRowStatus and
mplsTunnelResourceStorageType."::={ mplsTunnelResourceEntry 9}mplsTunnelResourceStorageType OBJECT-TYPESYNTAXStorageTypeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The storage type for this Hop entry. Conceptual
rows having the value 'permanent' need not
allow write-access to any columnar objects
in the row."DEFVAL{ volatile }::={ mplsTunnelResourceEntry 10}-- End mplsTunnelResourceTable-- Tunnel Actual Route Hop table.mplsTunnelARHopTable OBJECT-TYPESYNTAXSEQUENCEOF MplsTunnelARHopEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The mplsTunnelARHopTable is used to indicate the
hops for an MPLS tunnel defined in mplsTunnelTable,
as reported by the MPLS signalling protocol. Thus at
a transit LSR, this table (if the table is supported
and if the signaling protocol is recording actual
route information) contains the actual route of the
whole tunnel. If the signaling protocol is not
recording the actual route, this table MAY report
the information from the mplsTunnelHopTable or the
mplsTunnelCHopTable.
Each row in this table is indexed by
mplsTunnelARHopListIndex. Each row also has a
secondary index mplsTunnelARHopIndex, corresponding
to the next hop that this row corresponds to.
Please note that since the information necessary to
build entries within this table is not provided by
some MPLS signalling protocols, implementation of
this table is optional. Furthermore, since the
information in this table is actually provided by
the MPLS signalling protocol after the path has
been set-up, the entries in this table are provided
only for observation, and hence, all variables in
this table are accessible exclusively as read-
only.
Note also that the contents of this table may change
while it is being read because of re-routing
activities. A network administrator may verify that
the actual route read is consistent by reference to
the mplsTunnelLastPathChange object."::={ mplsTeObjects 7}mplsTunnelARHopEntry OBJECT-TYPESYNTAX MplsTunnelARHopEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in this table represents a tunnel hop. An
entry is created by the agent for signaled ERLSP
set up by an MPLS signalling protocol."INDEX{ mplsTunnelARHopListIndex, mplsTunnelARHopIndex }::={ mplsTunnelARHopTable 1}
MplsTunnelARHopEntry ::=SEQUENCE{
mplsTunnelARHopListIndex MplsPathIndex,
mplsTunnelARHopIndex MplsPathIndex,
mplsTunnelARHopAddrType TeHopAddressType,
mplsTunnelARHopIpAddr TeHopAddress,
mplsTunnelARHopAddrUnnum TeHopAddressUnnum,
mplsTunnelARHopLspId MplsLSPID}mplsTunnelARHopListIndex OBJECT-TYPE
SYNTAXMplsPathIndexMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Primary index into this table identifying a
particular recorded hop list."::={ mplsTunnelARHopEntry 1}mplsTunnelARHopIndex OBJECT-TYPESYNTAXMplsPathIndexMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Secondary index into this table identifying the
particular hop."::={ mplsTunnelARHopEntry 2}mplsTunnelARHopAddrType OBJECT-TYPESYNTAXTeHopAddressTypeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The Hop Address Type of this tunnel hop.
Note that lspid(5) is a valid option only
for tunnels signaled via CRLDP."DEFVAL{ ipv4 }::={ mplsTunnelARHopEntry 3}mplsTunnelARHopIpAddr OBJECT-TYPESYNTAXTeHopAddressMAX-ACCESSread-only
STATUScurrentDESCRIPTION"The Tunnel Hop Address for this tunnel hop.
The type of this address is determined by the
value of the corresponding mplsTunnelARHopAddrType.
If mplsTunnelARHopAddrType is set to unnum(4),
then this value contains the LSR Router ID of the
unnumbered interface. Otherwise the agent SHOULD
set this object to the zero-length string and the
manager should ignore this object."DEFVAL{ '00000000'h }-- IPv4 address 0.0.0.0::={ mplsTunnelARHopEntry 4}mplsTunnelARHopAddrUnnum OBJECT-TYPESYNTAXTeHopAddressUnnumMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If mplsTunnelARHopAddrType is set to unnum(4), then
this value will contain the interface identifier of
the unnumbered interface for this hop. This object
should be used in conjunction with
mplsTunnelARHopIpAddr which would contain the LSR
Router ID in this case. Otherwise the agent should
set this object to zero-length string and the
manager should ignore this."::={ mplsTunnelARHopEntry 5}mplsTunnelARHopLspId OBJECT-TYPESYNTAXMplsLSPIDMAX-ACCESSread-only
STATUScurrentDESCRIPTION"If mplsTunnelARHopAddrType is set to lspid(5), then
this value will contain the LSP ID of this hop.
This object is otherwise insignificant and should
contain a value of 0 to indicate this fact."::={ mplsTunnelARHopEntry 6}-- End of mplsTunnelARHopTable-- Tunnel Computed Hop table.mplsTunnelCHopTable OBJECT-TYPESYNTAXSEQUENCEOF MplsTunnelCHopEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The mplsTunnelCHopTable is used to indicate the
hops, strict or loose, for an MPLS tunnel defined
in mplsTunnelTable, as computed by a constraint-
based routing protocol, based on the
mplsTunnelHopTable for the outgoing direction of
the tunnel. Thus at a transit LSR, this table (if
the table is supported) MAY contain the path
computed by the CSPF engine on (or on behalf of)
this LSR. Each row in this table is indexed by
mplsTunnelCHopListIndex. Each row also has a
secondary index mplsTunnelCHopIndex, corresponding
to the next hop that this row corresponds to. In
case we want to specify a particular interface on
the originating LSR of an outgoing tunnel by which
we want packets to exit the LSR, we specify this as
the first hop for this tunnel in
mplsTunnelCHopTable.
Please note that since the information necessary to
build entries within this table may not be
supported by some LSRs, implementation of this
table is optional. Furthermore, since the
information in this table describes the path
computed by the CSPF engine the entries in this
table are read-only."::={ mplsTeObjects 8}mplsTunnelCHopEntry OBJECT-TYPESYNTAX MplsTunnelCHopEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in this table represents a tunnel hop. An
entry in this table is created by a path
computation engine using CSPF techniques applied to
the information collected by routing protocols and
the hops specified in the corresponding
mplsTunnelHopTable."INDEX{ mplsTunnelCHopListIndex, mplsTunnelCHopIndex }::={ mplsTunnelCHopTable 1}
MplsTunnelCHopEntry ::=SEQUENCE{
mplsTunnelCHopListIndex MplsPathIndex,
mplsTunnelCHopIndex MplsPathIndex,
mplsTunnelCHopAddrType TeHopAddressType,
mplsTunnelCHopIpAddr TeHopAddress,
mplsTunnelCHopIpPrefixLen InetAddressPrefixLength,
mplsTunnelCHopAsNumber TeHopAddressAS,
mplsTunnelCHopAddrUnnum TeHopAddressUnnum,
mplsTunnelCHopLspId MplsLSPID,
mplsTunnelCHopType INTEGER}mplsTunnelCHopListIndex OBJECT-TYPESYNTAXMplsPathIndexMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Primary index into this table identifying a
particular computed hop list."::={ mplsTunnelCHopEntry 1}mplsTunnelCHopIndex OBJECT-TYPESYNTAXMplsPathIndexMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Secondary index into this table identifying the
particular hop."::={ mplsTunnelCHopEntry 2}mplsTunnelCHopAddrType OBJECT-TYPESYNTAXTeHopAddressTypeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The Hop Address Type of this tunnel hop.
Note that lspid(5) is a valid option only
for tunnels signaled via CRLDP."
DEFVAL{ ipv4 }::={ mplsTunnelCHopEntry 3}mplsTunnelCHopIpAddr OBJECT-TYPESYNTAXTeHopAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The Tunnel Hop Address for this tunnel hop.
The type of this address is determined by the
value of the corresponding mplsTunnelCHopAddrType.
If mplsTunnelCHopAddrType is set to unnum(4), then
this value will contain the LSR Router ID of the
unnumbered interface. Otherwise the agent should
set this object to the zero-length string and the
manager SHOULD ignore this object."DEFVAL{ '00000000'h }-- IPv4 address 0.0.0.0::={ mplsTunnelCHopEntry 4}mplsTunnelCHopIpPrefixLen OBJECT-TYPESYNTAXInetAddressPrefixLengthMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If mplsTunnelCHopAddrType is set to ipv4(1) or
ipv6(2), then this value will contain an
appropriate prefix length for the IP address in
object mplsTunnelCHopIpAddr. Otherwise this value
is irrelevant and should be ignored.
"DEFVAL{32}
::={ mplsTunnelCHopEntry 5}mplsTunnelCHopAsNumber OBJECT-TYPESYNTAXTeHopAddressASMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If mplsTunnelCHopAddrType is set to asnumber(3),
then this value will contain the AS number of this
hop. Otherwise the agent should set this object to
zero-length string and the manager should ignore
this."::={ mplsTunnelCHopEntry 6}mplsTunnelCHopAddrUnnum OBJECT-TYPESYNTAXTeHopAddressUnnumMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If mplsTunnelCHopAddrType is set to unnum(4), then
this value will contain the unnumbered interface
identifier of this hop. This object should be used
in conjunction with mplsTunnelCHopIpAddr which
would contain the LSR Router ID in this case.
Otherwise the agent should set this object to zero-
length string and the manager should ignore this."::={ mplsTunnelCHopEntry 7}mplsTunnelCHopLspId OBJECT-TYPESYNTAXMplsLSPIDMAX-ACCESSread-only
STATUScurrentDESCRIPTION"If mplsTunnelCHopAddrType is set to lspid(5), then
this value will contain the LSP ID of this hop.
This object is otherwise insignificant and should
contain a value of 0 to indicate this fact."::={ mplsTunnelCHopEntry 8}mplsTunnelCHopType OBJECT-TYPESYNTAXINTEGER{ strict(1),loose(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Denotes whether this is tunnel hop is routed in a
strict or loose fashion."::={ mplsTunnelCHopEntry 9}-- End of mplsTunnelCHopTable-- MPLS Tunnel Performance Table.mplsTunnelPerfTable OBJECT-TYPESYNTAXSEQUENCEOF MplsTunnelPerfEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table provides per-tunnel instance MPLS
performance information."::={ mplsTeObjects 9}
mplsTunnelPerfEntry OBJECT-TYPESYNTAX MplsTunnelPerfEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in this table is created by the LSR for
every tunnel. Its is an extension to
mplsTunnelEntry."AUGMENTS{ mplsTunnelEntry }::={ mplsTunnelPerfTable 1}
MplsTunnelPerfEntry ::=SEQUENCE{
mplsTunnelPerfPackets Counter32,
mplsTunnelPerfHCPackets Counter64,
mplsTunnelPerfErrors Counter32,
mplsTunnelPerfBytes Counter32,
mplsTunnelPerfHCBytes Counter64}mplsTunnelPerfPackets OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of packets forwarded by the tunnel.
This object should represents the 32-bit
value of the least significant part of the
64-bit value if both mplsTunnelPerfHCPackets
is returned."::={ mplsTunnelPerfEntry 1}
mplsTunnelPerfHCPackets OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"High capacity counter for number of packets
forwarded by the tunnel. "::={ mplsTunnelPerfEntry 2}mplsTunnelPerfErrors OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of packets dropped because of errors or for
other reasons."::={ mplsTunnelPerfEntry 3}mplsTunnelPerfBytes OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of bytes forwarded by the tunnel.
This object should represents the 32-bit
value of the least significant part of the
64-bit value if both mplsTunnelPerfHCBytes
is returned."::={ mplsTunnelPerfEntry 4}mplsTunnelPerfHCBytes OBJECT-TYPESYNTAXCounter64
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"High capacity counter for number of bytes forwarded
by the tunnel."::={ mplsTunnelPerfEntry 5}-- End of mplsTunnelPerfTable-- CR-LDP Tunnel Resource TablemplsTunnelCRLDPResTable OBJECT-TYPESYNTAXSEQUENCEOF MplsTunnelCRLDPResEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The mplsTunnelCRLDPResTable allows a manager to
specify which CR-LDP-specific resources are desired
for an MPLS tunnel if that tunnel is signaled using
CR-LDP. Note that these attributes are in addition
to those specified in mplsTunnelResourceTable. This
table also allows several tunnels to point to a
single entry in this table, implying that these
tunnels should share resources."::={ mplsTeObjects 10}mplsTunnelCRLDPResEntry OBJECT-TYPESYNTAX MplsTunnelCRLDPResEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in this table represents a set of resources
for an MPLS tunnel established using CRLDP
(mplsTunnelSignallingProto equal to crldp (3)). An
entry can be created by a network administrator or
by an SNMP agent as instructed by any MPLS
signalling protocol."INDEX{ mplsTunnelResourceIndex }::={ mplsTunnelCRLDPResTable 1}
MplsTunnelCRLDPResEntry ::=SEQUENCE{
mplsTunnelCRLDPResMeanBurstSize MplsBurstSize,
mplsTunnelCRLDPResExBurstSize MplsBurstSize,
mplsTunnelCRLDPResFrequency INTEGER,
mplsTunnelCRLDPResWeight Unsigned32,
mplsTunnelCRLDPResFlags Unsigned32,
mplsTunnelCRLDPResRowStatus RowStatus,
mplsTunnelCRLDPResStorageType StorageType}mplsTunnelCRLDPResMeanBurstSize OBJECT-TYPESYNTAXMplsBurstSizeUNITS"bytes"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The mean burst size in bytes."::={ mplsTunnelCRLDPResEntry 1}mplsTunnelCRLDPResExBurstSize OBJECT-TYPESYNTAXMplsBurstSizeUNITS"bytes"
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The Excess burst size in bytes."REFERENCE"CR-LDP Specification, Section 4.3."::={ mplsTunnelCRLDPResEntry 2}mplsTunnelCRLDPResFrequency OBJECT-TYPESYNTAXINTEGER{unspecified(1),frequent(2),veryFrequent(3)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The granularity of the availability of committed
rate."REFERENCE"CR-LDP Specification, Section 4.3."::={ mplsTunnelCRLDPResEntry 3}mplsTunnelCRLDPResWeight OBJECT-TYPESYNTAXUnsigned32(0..255)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The relative weight for using excess bandwidth above
its committed rate. The value of 0 means that
weight is not applicable for the CR-LSP."REFERENCE"CR-LDP Specification, Section 4.3."DEFVAL{0}::={ mplsTunnelCRLDPResEntry 4}mplsTunnelCRLDPResFlags OBJECT-TYPESYNTAXUnsigned32(0..63)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The value of the 1 byte Flags conveyed as part of
the traffic parameters during the establishment of
the CRLSP. The bits in this object are to be
interpreted as follows.
+--+--+--+--+--+--+--+--+
| Res |F6|F5|F4|F3|F2|F1|
+--+--+--+--+--+--+--+--+
Res - These bits are reserved. Zero on transmission.
Ignored on receipt.
F1 - Corresponds to the PDR.
F2 - Corresponds to the PBS.
F3 - Corresponds to the CDR.
F4 - Corresponds to the CBS.
F5 - Corresponds to the EBS.
F6 - Corresponds to the Weight.
Each flag if is a Negotiable Flag corresponding to a
Traffic Parameter. The Negotiable Flag value zero
denotes Not Negotiable and value one denotes
Negotiable."REFERENCE"1. Section 4.3, Constraint-Based LSP Setup using
LDP, Jamoussi (Editor), RFC 3212, January 2002"
DEFVAL{0}::={ mplsTunnelCRLDPResEntry 5}mplsTunnelCRLDPResRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This variable is used to create, modify, and/or
delete a row in this table. When a row in this
table is in active(1) state, no objects in that row
can be modified by the agent except
mplsTunnelCRLDPResRowStatus and
mplsTunnelCRLDPResStorageType."::={ mplsTunnelCRLDPResEntry 6}mplsTunnelCRLDPResStorageType OBJECT-TYPESYNTAXStorageTypeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The storage type for this CR-LDP Resource entry.
Conceptual rows having the value 'permanent'
need not allow write-access to any columnar
objects in the row."DEFVAL{ volatile }::={ mplsTunnelCRLDPResEntry 7}-- Notifications.mplsTunnelNotificationEnable OBJECT-TYPESYNTAXTruthValue
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"If this object is true, then it enables the
generation of mplsTunnelUp and mplsTunnelDown
traps, otherwise these traps are not emitted."DEFVAL{ false }::={ mplsTeObjects 11}mplsTunnelUp NOTIFICATION-TYPEOBJECTS{
mplsTunnelAdminStatus,
mplsTunnelOperStatus
}STATUScurrentDESCRIPTION"This notification is generated when a
mplsTunnelOperStatus object for one of the
configured tunnels is about to leave the down state
and transition into some other state (but not into
the notPresent state). This other state is
indicated by the included value of
mplsTunnelOperStatus."::={ mplsTeNotifications 1}mplsTunnelDown NOTIFICATION-TYPEOBJECTS{
mplsTunnelAdminStatus,
mplsTunnelOperStatus
}STATUScurrentDESCRIPTION"This notification is generated when a
mplsTunnelOperStatus object for one of the
configured tunnels is about to enter the down state
from some other state (but not from the notPresent
state). This other state is indicated by the
included value of mplsTunnelOperStatus."::={ mplsTeNotifications 2}mplsTunnelRerouted NOTIFICATION-TYPEOBJECTS{
mplsTunnelAdminStatus,
mplsTunnelOperStatus
}STATUScurrentDESCRIPTION"This notification is generated when a tunnel is
rerouted. If the mplsTunnelARHopTable is used, then
this tunnel instance's entry in the
mplsTunnelARHopTable MAY contain the new path for
this tunnel some time after this trap is issued by
the agent."::={ mplsTeNotifications 3}mplsTunnelReoptimized NOTIFICATION-TYPEOBJECTS{
mplsTunnelAdminStatus,
mplsTunnelOperStatus
}STATUScurrentDESCRIPTION"This notification is generated when a tunnel is
reoptimized. If the mplsTunnelARHopTable is used,
then this tunnel instance's entry in the
mplsTunnelARHopTable MAY contain the new path for
this tunnel some time after this trap is issued by
the agent."::={ mplsTeNotifications 4}-- End of notifications.-- Module compliance.mplsTeGroups
OBJECTIDENTIFIER::={ mplsTeConformance 1}mplsTeCompliances
OBJECTIDENTIFIER::={ mplsTeConformance 2}-- Compliance requirement for fully compliant implementations.mplsTeModuleFullCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"Compliance statement for agents that provide full
support the MPLS-TE-STD-MIB module."MODULE IF-MIB -- The Interfaces Group MIB, RFC 2863.MANDATORY-GROUPS{
ifGeneralInformationGroup,
ifCounterDiscontinuityGroup
}MODULE-- this module-- The mandatory group has to be implemented by all-- LSRs that originate/terminate ESLSPs/tunnels.-- In addition, depending on the type of tunnels-- supported, other groups become mandatory as-- explained below.MANDATORY-GROUPS{
mplsTunnelGroup,
mplsTunnelScalarGroup
}GROUP mplsTunnelManualGroup
DESCRIPTION"This group is mandatory for devices which support
manual configuration of tunnels."GROUP mplsTunnelSignaledGroup
DESCRIPTION"This group is mandatory for devices which support
signaled tunnel set up."GROUP mplsTunnelIsNotIntfcGroup
DESCRIPTION"This group is mandatory for devices which support
tunnels that are not interfaces."GROUP mplsTunnelIsIntfcGroup
DESCRIPTION"This group is mandatory for devices which support
tunnels that are interfaces."GROUP mplsTunnelCRLDPResOptionalGroup
DESCRIPTION"Objects in this group are required by
implementations supporting the CR-LDP protocol for
signalling of TE tunnels."GROUP mplsTeNotificationGroup
DESCRIPTION"This group is mandatory for those implementations
which can implement the notifications
contained in this group."OBJECT mplsTunnelRowStatus
SYNTAXRowStatus{ active(1), notInService(2)}WRITE-SYNTAXRowStatus{ active(1), notInService(2),
createAndGo(4), destroy(6)}
DESCRIPTION"Support for createAndWait and notReady is not
required."OBJECT mplsTunnelHopRowStatus
SYNTAXRowStatus{ active(1), notInService(2)}WRITE-SYNTAXRowStatus{ active(1), notInService(2),
createAndGo(4), destroy(6)}DESCRIPTION"Support for createAndWait and notReady is not
required."OBJECT mplsTunnelCRLDPResRowStatus
SYNTAXRowStatus{ active(1), notInService(2)}WRITE-SYNTAXRowStatus{ active(1), notInService(2),
createAndGo(4), destroy(6)}DESCRIPTION"Support for createAndWait and notReady is
not required."::={ mplsTeCompliances 1}-- Compliance requirement for read-only implementations.mplsTeModuleReadOnlyCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"Compliance requirement for implementations that only
provide read-only support for MPLS-TE-STD-MIB.
Such devices can then be monitored but cannot be
configured using this MIB modules."MODULE-- this module-- mplsTunnelTableMANDATORY-GROUPS{
mplsTunnelGroup,
mplsTunnelScalarGroup
}GROUP mplsTunnelManualGroup
DESCRIPTION"This group is mandatory for devices which support
manual configuration of tunnels."GROUP mplsTunnelSignaledGroup
DESCRIPTION"This group is mandatory for devices which support
signaled tunnel set up."GROUP mplsTunnelIsNotIntfcGroup
DESCRIPTION"This group is mandatory for devices which support
tunnels that are not interfaces."GROUP mplsTunnelIsIntfcGroup
DESCRIPTION"This group is mandatory for devices which support
tunnels that are interfaces."GROUP mplsTunnelCRLDPResOptionalGroup
DESCRIPTION"Objects in this group are required by
implementations supporting the CR-LDP protocol for
signalling of TE tunnels."GROUP mplsTeNotificationGroup
DESCRIPTION"This group is mandatory for those implementations
which can implement the notifications
contained in this group."-- mplsTunnelTableOBJECT mplsTunnelName
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelDescr
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelIsIf
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelIfIndex
DESCRIPTION"Write access is not required."OBJECT mplsTunnelXCPointer
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelSignallingProto
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelSetupPrio
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelHoldingPrio
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelSessionAttributes
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelLocalProtectInUse
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelResourcePointer
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelInstancePriority
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelHopTableIndex
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelIncludeAnyAffinity
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelIncludeAllAffinity
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelExcludeAnyAffinity
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelPathInUse
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelRole
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelAdminStatus
SYNTAXINTEGER{ up (1), down (2)}MIN-ACCESSread-onlyDESCRIPTION"Only up and down states must be supported. Write
access is not required."OBJECT mplsTunnelRowStatus
SYNTAXRowStatus{ active(1)}MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."-- mplsTunnelHopTableOBJECT mplsTunnelHopAddrType
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelHopIpAddr
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelHopIpPrefixLen
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelHopAddrUnnum
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelHopAsNumber
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelHopLspId
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelHopType
SYNTAXINTEGER{ strict(1)}MIN-ACCESSread-onlyDESCRIPTION"loose(2) need not be supported. Write access is
not required."OBJECT mplsTunnelHopInclude
MIN-ACCESSread-only
DESCRIPTION"Write access is not required."OBJECT mplsTunnelHopPathOptionName
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelHopEntryPathComp
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelHopRowStatus
SYNTAXRowStatus{ active(1)}MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelHopStorageType
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."-- mplsTunnelResourceTableOBJECT mplsTunnelResourceMaxRate
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelResourceMeanRate
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelResourceMaxBurstSize
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."
OBJECT mplsTunnelResourceMeanBurstSize
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelResourceExBurstSize
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelResourceFrequency
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelResourceWeight
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelResourceRowStatus
SYNTAXRowStatus{ active(1)}MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelResourceStorageType
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."-- mplsTunnelCRLDPResTableOBJECT mplsTunnelCRLDPResMeanBurstSize
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelCRLDPResExBurstSize
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelCRLDPResFrequency
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelCRLDPResWeight
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelCRLDPResFlags
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelCRLDPResRowStatus
SYNTAXRowStatus{ active(1)}MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT mplsTunnelCRLDPResStorageType
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."::={ mplsTeCompliances 2}-- Units of conformance.mplsTunnelGroup OBJECT-GROUPOBJECTS{
mplsTunnelIndexNext,
mplsTunnelName,
mplsTunnelDescr,
mplsTunnelOwner,
mplsTunnelXCPointer,
mplsTunnelIfIndex,
mplsTunnelHopTableIndex,
mplsTunnelARHopTableIndex,
mplsTunnelCHopTableIndex,
mplsTunnelAdminStatus,
mplsTunnelOperStatus,
mplsTunnelRowStatus,
mplsTunnelNotificationEnable,
mplsTunnelStorageType,
mplsTunnelConfigured,
mplsTunnelActive,
mplsTunnelPrimaryInstance,
mplsTunnelPrimaryUpTime,
mplsTunnelPathChanges,
mplsTunnelLastPathChange,
mplsTunnelCreationTime,
mplsTunnelStateTransitions,
mplsTunnelIncludeAnyAffinity,
mplsTunnelIncludeAllAffinity,
mplsTunnelExcludeAnyAffinity,
mplsTunnelPerfPackets,
mplsTunnelPerfHCPackets,
mplsTunnelPerfErrors,
mplsTunnelPerfBytes,
mplsTunnelPerfHCBytes,
mplsTunnelResourcePointer,
mplsTunnelInstancePriority,
mplsTunnelPathInUse,
mplsTunnelRole,
mplsTunnelTotalUpTime,
mplsTunnelInstanceUpTime,
mplsTunnelResourceIndexNext,
mplsTunnelResourceMaxRate,
mplsTunnelResourceMeanRate,
mplsTunnelResourceMaxBurstSize,
mplsTunnelResourceMeanBurstSize,
mplsTunnelResourceExBurstSize,
mplsTunnelResourceFrequency,
mplsTunnelResourceWeight,
mplsTunnelResourceRowStatus,
mplsTunnelResourceStorageType,
mplsTunnelARHopAddrType,
mplsTunnelARHopIpAddr,
mplsTunnelARHopAddrUnnum,
mplsTunnelARHopLspId,
mplsTunnelCHopAddrType,
mplsTunnelCHopIpAddr,
mplsTunnelCHopIpPrefixLen,
mplsTunnelCHopAsNumber,
mplsTunnelCHopAddrUnnum,
mplsTunnelCHopLspId,
mplsTunnelCHopType
}STATUScurrentDESCRIPTION"Necessary, but not sufficient, set of objects to
implement tunnels. In addition, depending on the
type of the tunnels supported (for example,
manually configured or signaled, persistent or non-
persistent, etc.), the following other groups
defined below are mandatory: mplsTunnelManualGroup
and/or mplsTunnelSignaledGroup,
mplsTunnelIsNotIntfcGroup and/or
mplsTunnelIsIntfcGroup."::={ mplsTeGroups 1}mplsTunnelManualGroup OBJECT-GROUPOBJECTS{ mplsTunnelSignallingProto }STATUScurrentDESCRIPTION"Object(s) needed to implement manually configured
tunnels."::={ mplsTeGroups 2}mplsTunnelSignaledGroup OBJECT-GROUPOBJECTS{
mplsTunnelSetupPrio,
mplsTunnelHoldingPrio,
mplsTunnelSignallingProto,
mplsTunnelLocalProtectInUse,
mplsTunnelSessionAttributes,
mplsTunnelHopListIndexNext,
mplsTunnelHopAddrType,
mplsTunnelHopIpAddr,
mplsTunnelHopIpPrefixLen,
mplsTunnelHopAddrUnnum,
mplsTunnelHopAsNumber,
mplsTunnelHopLspId,
mplsTunnelHopType,
mplsTunnelHopInclude,
mplsTunnelHopPathOptionName,
mplsTunnelHopEntryPathComp,
mplsTunnelHopRowStatus,
mplsTunnelHopStorageType
}STATUScurrentDESCRIPTION"Objects needed to implement signaled tunnels."::={ mplsTeGroups 3}mplsTunnelScalarGroup OBJECT-GROUPOBJECTS{
mplsTunnelConfigured,
mplsTunnelActive,
mplsTunnelTEDistProto,
mplsTunnelMaxHops,
mplsTunnelNotificationMaxRate
}STATUScurrent
DESCRIPTION"Scalar object needed to implement MPLS tunnels."::={ mplsTeGroups 4}mplsTunnelIsIntfcGroup OBJECT-GROUPOBJECTS{ mplsTunnelIsIf }STATUScurrentDESCRIPTION"Objects needed to implement tunnels that are
interfaces."::={ mplsTeGroups 5}mplsTunnelIsNotIntfcGroup OBJECT-GROUPOBJECTS{ mplsTunnelIsIf }STATUScurrentDESCRIPTION"Objects needed to implement tunnels that are not
interfaces."::={ mplsTeGroups 6}mplsTunnelCRLDPResOptionalGroup OBJECT-GROUPOBJECTS{
mplsTunnelCRLDPResMeanBurstSize,
mplsTunnelCRLDPResExBurstSize,
mplsTunnelCRLDPResFrequency,
mplsTunnelCRLDPResWeight,
mplsTunnelCRLDPResFlags,
mplsTunnelCRLDPResRowStatus,
mplsTunnelCRLDPResStorageType
}STATUScurrentDESCRIPTION"Set of objects implemented for resources applicable
for tunnels signaled using CR-LDP."::={ mplsTeGroups 7}mplsTeNotificationGroup NOTIFICATION-GROUPNOTIFICATIONS{
mplsTunnelUp,
mplsTunnelDown,
mplsTunnelRerouted,
mplsTunnelReoptimized
}STATUScurrentDESCRIPTION"Set of notifications implemented in this module.
None is mandatory."::={ mplsTeGroups 8}END